Copper Nickel Fasteners Supplier and exporter in India
Home > Copper Nickel Products > Copper Nickel Sheets and Plates
Copper nickel sheets and plates are flat metal products used in marine equipment, heat exchangers, condensers and desalination systems exposed to seawater. Aashish Metals offers 90/10 copper nickel (UNS C70600) and 70/30 copper nickel (UNS C71500) for industrial fabrication requirements. The 90/10 grade contains approximately 10% nickel, while the 70/30 grade contains approximately 30% nickel, with iron and manganese contributing to their material properties. Both grades have a typical density of around 8.94 g/cm³ and offer good resistance to seawater corrosion and biofouling. These copper nickel sheets and plates are selected for components such as tubesheets, water boxes and marine cladding, with grade selection based on service conditions, fabrication requirements and project specifications.
Technical data
Specifications of Copper Nickel Sheets & Plates
| Parameter | Detail |
|---|---|
| Specifications | ASTM B171, B122 / ASME SB171, SB122. B171 for pressure vessels, condensers and heat exchangers; B122 for general plate, sheet, strip and rolled bar. |
| Standards | ASTM B171, B122; ASME SB171, SB122; EN 10204 3.1 certificate |
| Size | Thickness 1 mm to 100 mm; width up to 1500 mm; length up to 3000 mm |
| Finishing | Hot rolled plate (HR), cold rolled sheet (CR), mill finish, pickled |
| Form | Sheet, plate, cut to size, circles (blanks) and rings |
| Hardness | Soft (annealed), half hard (H02), hard (H04) |
| Grade | UNS C70600 (Cu-Ni 90/10), UNS C71500 (Cu-Ni 70/30) |
Chemical Composition of Copper Nickel Sheets & Plates
| Grade | Cu | Pb | Mn | Fe | Zn | Ni |
|---|---|---|---|---|---|---|
| Cupro Nickel 90/10 | 88.6 min | 0.05 max | 1.0 max | 1.0 – 1.8 | 1.0 max | 9.0 – 11.0 |
| Cupro Nickel 70/30 | 65.0 min | 0.05 max | 1.0 max | 0.4 – 1.0 | 1.0 max | 29.0 – 33.0 |
Cu-Ni Sheets / Plate Mechanical Properties
| Property | Cu-Ni 90/10 (C70600) | Cu-Ni 70/30 (C71500) |
|---|---|---|
| Density | 8.94 g/cm³ (0.323 lb/in³) | 8.94 g/cm³ (0.323 lb/in³) |
| Melting range | 1100 to 1145 °C | 1170 to 1240 °C |
| Tensile strength (annealed, typical) | about 275 MPa (40,000 psi) | about 370 MPa (54,000 psi) |
| Yield strength 0.2% (annealed, typical) | about 105 MPa (15,000 psi) | about 140 MPa (20,000 psi) |
| Elongation (typical) | 30% min | 30% min |
Copper Nickel Equivalent Grade
| Common name | UNS | Werkstoff No. | EN designation |
|---|---|---|---|
| Cu-Ni 90/10 | C70600 | 2.0872 | CuNi10Fe1Mn |
| Cu-Ni 70/30 | C71500 | 2.0882 | CuNi30Mn1Fe |
Types of Copper Nickel Sheets/Plates
Applications of Copper Nickel Sheets and Plates
Copper nickel sheets and plates are used in equipment where seawater exposure and corrosion resistance are important considerations.
- Heat exchanger tubesheets: Used in heat exchanger construction where the material is exposed to seawater and requires corrosion resistance.
- Condenser components: Selected for condenser parts in marine and power generation systems handling cooling water.
- Desalination equipment: Used in suitable equipment and fabricated components exposed to saline water.
- Shipbuilding and hull sheathing: Applied in marine construction where resistance to seawater corrosion and biofouling is required.
- Offshore splash zone components: Considered for suitable components exposed to seawater spray and changing marine conditions.
- Seawater piping equipment: Used to fabricate associated plates, water boxes and components in seawater handling systems.
The required grade depends on seawater velocity, operating conditions, component design and the applicable material specification. Contact Aashish Metals with your material and dimensional requirements.
Frequently Asked Questions
They are used for heat exchanger and condenser tubesheets, water boxes, desalination equipment, shipbuilding and hull sheathing, and offshore splash zone cladding, wherever seawater would corrode steel.
We supply 90/10 (UNS C70600) and 70/30 (UNS C71500). Grade 90/10 suits condensers and general marine use, while 70/30 is stronger and more resistant to erosion.
ASTM B171 covers plate and sheet for pressure vessels, condensers and heat exchangers. ASTM B122 covers copper nickel plate, sheet, strip and rolled bar for general use. Specify the one your project requires.
Standard sheet sizes include 1250 x 2500 mm, 1219 x 2438 mm and 1500 x 3000 mm, and we cut to size on request. Send us your thickness, width and length and we confirm what we can supply.
Multiply the thickness in mm by 8.94 to get kg per square meter. A 10 mm plate weighs about 89.4 kg per square meter, so a 1250 x 2500 mm sheet weighs about 279 kg.
Yes. It welds with matching copper nickel filler and forms well cold or hot. Keep tools free of steel contamination and follow the procedure for your grade and thickness.
Request a Quote for Copper Nickel Sheets & Plates
Similar products
Products
Please feel free to contact us. We will get back to you with 2 business days. Or just call us now.


